By Pridemark Plumbing · Licensed Arizona Contractor, ROC #319398
You don’t think much about your tankless water heater until something new shows up on it, like crusty buildup on tankless water heater pipes or a green stain on the copper. In August 2026, a homeowner in the Cortessa community of Waddell, Arizona 85355 called Pridemark Plumbing about mineral deposits on their Navien. Those deposits led us to a leak.
The short version: In August 2026, Pridemark Plumbing traced crusty buildup on a Navien NPE-240A tankless water heater in Waddell, Arizona, to two failed dielectric unions, fittings that join different metals. Both were leaking, rusted and clogged with brown scale inside. We took them out, put a new check valve in the right place, added a small expansion tank and serviced the heater. We also pointed out a gas line about half the size it needs to be, and the homeowner left it as it is.

Why Is There Crusty Buildup on My Tankless Water Heater?
Crusty buildup on a tankless water heater can start with a fitting that seeps so slowly the water dries before it drips. What’s left is whatever the water was carrying. EPCOR’s 2025 water figures say that in most cases, “the deposits or sediments left behind after water evaporates are calcium carbonate.”
Your heater’s gas and water connections all sit close together under the cabinet, so when you see crust, look at where it sits. At this home, the heaviest of it sat on two fittings below the heater, not on the heater itself.
Does Crust on a Water Heater Fitting Mean It’s Leaking?
Crust on a water heater fitting can mean a slow leak, and at this Waddell home it did. Donnie, our plumber on this job, followed the deposits to two dielectric unions under the Navien, and water was leaking from them. To check yours, clean the crust off and watch the spot: if fresh crust comes back, water’s still getting out.
A leak at a fitting is also a different job from one inside the heater, like the Rinnai heat exchanger leak we found in Glendale. So your first step is finding where the water’s coming from.
Seeing crust or rust under your tankless?
Give us a call and we’ll find where the water’s coming from. Pridemark Plumbing is based in Surprise and works across the West Valley.
What Is a Dielectric Union, and How Can You Tell It’s Failing?
A dielectric union is a fitting that joins two different metals, such as copper and steel, with an insulating layer inside that keeps them from reacting. From the outside, you’re looking for clues. On this job, those were heavy rust at the collar and white and green staining on the copper beside it. The EPA’s drinking water guidance links “blue-green staining” to copper and “reddish or orange staining” to iron, so the color can hint at which metal’s involved.
The inside told the rest. Once Donnie had them off, both were heavily rusted and clogged with brown scale, a hard crust that can build up inside pipes and fittings. He puts that scale down to the area’s water quality.
Donnie’s advice: if a job requires a dielectric union, it has to be installed properly. On this job, dielectric unions weren’t required, so both came out and none went back. “I also use brass connectors,” he says, “to avoid the galvanic corrosion issues we see with the standard dielectric unions.” That’s the metal-on-metal reaction those unions are meant to stop.
Brass connectors are his practice from his own jobs, so ask your plumber what they’d use and why. Navien’s installation manual recommends unions, fittings that let a pipe come apart, and shut-off valves on the water lines. The only thing it says about the dielectric kind is that they “may prevent proper grounding” if a heater’s ground wire is tied to the piping.
How Hard Is the Water in Waddell, AZ?
In Waddell, Arizona, EPCOR’s 2025 water quality figures for its Agua Fria district run from 2 to 17 grains per gallon of hardness, the usual measure of hardness minerals. Navien’s installation manual for the NPE-240A, the model on this job, lists 12 grains, or 200 milligrams per liter, as the maximum. So the top of EPCOR’s range runs past Navien’s line.
EPCOR’s supply contains both surface water and groundwater, and it says hardness can shift with the seasons. There’s no hardness reading on record at this home, so test at your own tap instead of going by the range. We ran the same EPCOR numbers against Rinnai’s limit on a tankless maintenance job in Verrado.
How Do You Fix Leaking Unions Under a Tankless Water Heater?
You fix leaking unions by taking them out, because cleaning the outside does nothing for the inside. Here’s the work Pridemark Plumbing did at this Cortessa home in August 2026, listed by job and not in the order it happened, so you know what to ask about at yours:
- Removed the two failed dielectric unions.
- Put in a tee, a T-shaped fitting that joins three pipes, in their place.
- Installed a new check valve, a one-way valve for water, on the copper run below the heater. The old one sat in the wrong place.
- Added a small expansion tank, a tank with a cushion of air that gives heated water room to grow.
- Gave the Navien its annual service and descale, which runs a cleaning solution through the heat exchanger, the metal part where the burner’s heat moves into the water.
- Showed the homeowner the undersized gas line.

We cleaned the cold water inlet filter, a small screen that catches grit before it reaches the heater, and the air intake screen. We checked the venting, the pipes that carry exhaust outside, and cleaned the condensate trap, the part that collects the water a condensing heater makes. Then we ran a leak check with an electronic gas detector and went over the heater against Navien’s own checklist.
Want the fittings under your tankless checked the same way while your heater’s serviced? We’ll look over the unions and valves, then flush and descale the heater before we leave. New to Pridemark Plumbing? Show the $30 new-customer coupon on your phone.
Does a Tankless Water Heater Need an Expansion Tank?
A tankless water heater on a closed water system needs some way to handle thermal expansion, Navien says, and an expansion tank is one way to do it. Thermal expansion means water grows a little as it heats. A closed system is one where a check valve or backflow preventer keeps that extra water from pushing back toward the street.
Donnie’s reasoning on this job starts there. Most newer homes are closed systems, he says, and newer water meters have a check valve built in, which closes the system too. Add a recirculation line, which keeps hot water moving toward your faucets, and he says you need both an expansion tank and a check valve.
Navien’s manual says that on a closed system, “means shall be provided to control thermal expansion,” and to ask your water supplier or local plumbing inspector how.
The NPE-240A is an A model, which has a built-in recirculation pump. The typical piping example for A models in its installation manual shows an expansion tank on the cold water supply and a recirculation line. The example for S models, which have no built-in pump, shows neither. The manual adds that a relief valve, the safety valve on the hot side, that discharges now and then may point to thermal expansion.
You may hear that code calls for a tank. Maricopa County’s 2022 code document, in force when this job was done, adopts the 2018 plumbing code for unincorporated areas, and a Colorado memo quoting that code’s section on this shows a rule worded around “a storage water heater.”
North Carolina’s fire marshal’s office says of its own 2018 code: “An expansion device is not required for a tankless water heater that is not in a closed loop recirculation system.” Donnie’s reason for the tank on this job is the other side of that line: a closed system with recirculation. On any tankless, we go by the heater’s manual and the inspector’s answer.
Does a Tankless Water Heater Need a Check Valve?
Whether a tankless water heater needs a check valve depends on how it’s plumbed. With a recirculation line, Donnie’s answer is yes: the check valve keeps hot water from being pumped into the cold side every time someone uses cold water.
On this Navien, the old check valve sat in the wrong place, so Donnie put a new one where it belongs. Navien’s January 2026 manual for its newer A2 models shows one in its typical piping example, marked for reference only: a check valve ahead of the expansion tank on the cold water supply.
A check valve on the supply can also make a system closed, so the tank and valve questions go together. If your heater has a recirculation line, ask your plumber where its check valve sits and why.
Is the Gas Line Big Enough for Your Tankless Water Heater?
Your gas line might not be big enough, and a plumber can tell you by checking its length and diameter against your heater’s required BTUs, its rated gas demand. Navien’s checklist asks whether the gas supply line is “sufficient in length and diameter to deliver the required BTUs.”
During this August 2026 visit, Pridemark Plumbing’s Donnie found the gas line feeding this Navien about half the size it needs to be. He showed the homeowner, and the homeowner chose not to upgrade it, which is their call.
Donnie runs into undersized gas lines on tankless jobs around the West Valley. As he puts it, the heater gets starved for gas, runs lean and overheats, and over time that can damage the heat exchanger. Navien’s manual says the heater “cannot function properly without sufficient inlet gas pressure,” and its warranty page excludes “Performance problems caused by improper sizing” of the gas supply line, so it’s worth knowing where yours stands.
If your tankless struggles when two showers run at once, or your water temperature swings up and down, the gas supply is one thing to check. Our gas line page covers that work.
Should You Fix a Leaking Fitting Now or Wait?
Fix it now, because a fitting that’s already failed won’t heal on its own. At this home, those two failed unions are gone, the Navien stayed in place and got its service, and the homeowner knows where the gas line stands. Our Service Agreement is one way to keep your yearly checks on the calendar.

Why Call a Plumber Instead of Tightening It Yourself?
Snugging a fitting can hide a leak for a while without fixing what’s inside it. Water, gas and venting all come together in a small space under your heater, and Navien says installation and service “must be performed by a qualified installer, service agency or the gas supplier.”
You can still help: look for fresh crust or a damp spot, and write down any code on the display. Our tankless water heater page, Navien page and Waddell plumbing page cover the rest of what we do.
What Warranty Came With This Work?
This job’s paperwork reads: “Backed by Pridemark Plumbing’s 2-year warranty on all parts and labor, plus a 6-year manufacturer warranty on the expansion tank through Wolverine Brass.” The 2 years cover our own work on this job. Your Navien carries its own warranty from Navien, so read yours for what it covers.
Questions Homeowners Ask About Crust on a Tankless Water Heater
Can you just clean the crust off the fittings on a tankless water heater?
You can, and it’s a fair way to see whether a fitting is still seeping. If fresh crust comes back, water’s still getting out. At a Waddell, Arizona, home Pridemark Plumbing serviced in August 2026, cleaning wouldn’t have been enough, because two dielectric unions had failed: both were rusted and clogged with brown scale inside.
Does Navien’s warranty cover mineral buildup?
Not according to Navien’s warranty page for its NPE-A heaters, the series this job’s NPE-240A belongs to. It excludes “Any damage caused by local adverse conditions including but not limited to hard water deposits, lime or mineral build-up,” along with failure to perform regular maintenance. Keep your service records, and read the warranty for your exact model.
How often should a Navien tankless water heater be flushed?
Navien says “annual maintenance is recommended,” and that “If you have hard water, you may need to perform maintenance more often.” Its list covers the inlet water filter, the intake air filter, the condensate trap and a flush of the heat exchangers. A hardness test at your tap can help your plumber set the schedule for your home.
Does Pridemark Plumbing work on Navien tankless water heaters in Surprise, AZ?
Yes. Pridemark Plumbing is based in Surprise, Arizona, and works across the West Valley, including this job in the Cortessa community of Waddell. We service Navien tankless water heaters, and when we’re at yours, we’ll look over the fittings and the gas line and tell you what we see.
Crusty buildup on tankless water heater pipes? Rust at a fitting? A damp spot under the heater?
Any of those is worth a call. We’re a licensed, local West Valley plumber (ROC #319398). When we get there, we’ll find where the water’s coming from and walk you through what we see.
Call 623.239.2606 Request a visit online
First visit with us? Show the $30 new-customer coupon on your phone.